Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Book Your AppointmentAre you in search of help concerning How to Install a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately difficult project. If the old bathtub is conveniently available, the task can relocate easily; if you have to open up a wall surface to remove the old bathtub and position the new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly require a helper to vacate the old tub and also set in the new one. See to it you have actually qualified on your own for the work and also are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is far better to think about employing one prior to you start. Possibilities are you may need an expert plumber to make tube links.
This short article will help you install a new bath tub in your washroom if you have actually currently acquired a brand-new bathtub as well as do not need to transform the setup of your previous supply of water pipelines.
Your tools and also product checklist must consist of the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite problematic as a result of the restricted access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in place in between the faucet and also the sink. Secure the tap in place with the manufacturer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous type ought to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of both wood boards under its feet, position the bath tub in the called for setting. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub until the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the supply of water as well as examine all joints and also new pipework for leaks and tighten them if required. Load the bathtub as well as also examine the overflow outlet as well as the normal outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait up until the bathtub has been utilized at least when as this will certainly resolve it into its final position.
Planning for the Installation
First of all, the sustaining framework supplied with the bathroom needs to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps unit to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, resulting in problems with dampness and feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water before securing, to allow for the movement experienced when the tub is in usage. The sealer can crack rather very early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is suggested to fit the floor tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on How to Install a Bathtub, I assumed sharing that piece was really useful. Enjoyed our blog posting? Please share it. Let another person check it out. Bless you for your time. Kindly pay a visit to our website back soon.
For instant relief, call.